Don’t you just find it so ridiculously annoying when your toilet is often clogging? So what’s preventing you from fixing it once and for all?

Back in 2008 I had the same problem. My home toilet often clogged and my home smelled like filth. The plumber was on my speed dial! It took me a while to find a permanent solution to my problem and once I did I have never had those smelly sleepless nights again.

There are many solutions to unclogging a toilet. The choice is often yours. However, in this post I will tell you the one formula that I love the most; unclogging your toilet using the best toilet plunger. It is simple, it is easy, and you’ll have your toilet back up and running in no time.

You don’t have to flood the floor neither do you have to come out while looking like trash. Using a toilet plunger is simple and all you’ve got to is follow the steps that I am going to give you here.

Test Your Toilet for the Clog

Testing your toilet helps you to identify to what extent your flush toilet are clogged before you actually begin to unclog it using your plunger.

Usually, when your toilet doesn’t flush, it might mean two things; that your toilet is either completely clogged or somewhat clogged.

If the water fills your toilet bowl to the brim and even overflows onto the floor without flushing, it means that the toilet is completely blocked. You don’t have to run any big test. That’s how simple it is.

And if the water level drops slowly and doesn’t have enough thrust to clean the waste then the toilet is partially clogged. In both occasions you should allow the water levels to go down before you plunge your toilet.

Unclogging Your Flush Toilet

Unclogging your clogged toilet using a plunger is really simple; and trusts me in many occasions a plunger is all you need. Once you buy the best plunger, here is what you should really do to get your toilet back up.

Step 1

Get the best toilet gears and equipment for unclogging any backed up toilet. Sometimes unclogging a backed up toilet can be a really messy affair – but not every day. Dirty water can easily splash all over your face and leave you smelling of filth. But as a precaution and to say clean through the process, have gloves, an overall, mouth and eyes covers, and gum boots on before you resort to unclogging thee toilet.

Step 2

Allow the water level in the toilet bowl to go down. If your toilet is completely clogged, this might not be possible. So instead of waiting, you can get a bucket and a tin and draw the stagnant water out of the toilet bowl.

Once the water levels in the toilet bowl have gone down, remove the toilet’s tank lid. Slightly lift the toilet’s flapper valve and let a small amount of water in your toilet bowl. Don’t allow too much water it could flood your floor.

#To do this, you will need to lift up the toilet flapper just a little bit up and for a very short time; keep an eye on the water that slips to the bowl.

Step 3

Now it’s time to start plunging your toilet. Get your best toilet plunger and follow these instructions closely. It is important that you remain keen to the last moment when plunging your toilet.

Get the best seal. Pull out your rubber flange. Then fix the plunger inside the toilet bowl drain. This should give you a better seal. Getting a good seal will help you to create the right type of thrust that you need to unclog your toilet.

You can equally make your first plunge as gentle as possible to allow any trapped air to flow out of the plunger’s bell shaped rubber head. If you don’t do this, trapped air might come through vigorously and splash you up with dirty toilet water.

Step 4

Once the trapped air is out and the toilet plunger’s seal is compact, you should plunge vigorously. Push the plunger hard in an inward and outward motion. Make sure you keep enough water in the toilet bowl.

Here is how you can tell if the water in the toilet bowl is ideal for plunging of not: Always make sure that the water in the toilet bowl should always keep plunger bell-head submerged under it too.

Step 5

Keep on plunging for some time. You can alternate between monster heaves and simple steady plunger strokes too. This is important in making sure that you keep yourself and your shower room clean, and at the same time get the job done. Do this until the flow becomes very smooth.

What You Must Know When Using a Plunger

In order to get the best job done using your best toilet plunger, it is important that you keep an eye to the following things.

• Make sure the plunger head is always submerged in the water in the bowl.

• Get a proper seal before you start to plunge your backed up flush toilet.

• The first thrust should always be as gentle as you can to prevent splash.

• Shut off the water supply to the toilet to prevent any form of flood.

• Clean your toilet after plunging and before you resume to using it.

It is not an easy task if you have never done it before. However, with my type of experience you can actually love this job. Nonetheless if the clog refuses to go you can call on a professional to give you the right advice and help. Don’t force yourself to do it alone!

Conclusion

In many occasions a toilet plunger is enough to do the job – works for me! However, if it persists you can try some other tips from the experts. Toiletrated.com has some of the best unclogging tips and plunger reviews that will easily help you.

comments